Install the valve lifters and shims. Remove the valve lifters and shims. Slide the timing pulley on the camshaft with the flange side facing outward. Disconnect the vacuum hose from the gas filter. Mount the hexagon wrench head portion of the camshaft in a vise. At the click of a mouse you have access to the most comprehensive diagnostic, repair and maintenance information as used by professional mechanics, technicians and repair workshops.
Remove the valve lifters and shims from the cylinder head. Toyota Matrix Toyota Matrix 2003-2007 Repair Manual — Collection of manuals for maintenance and repair of Toyota Matrix 2003-2007. Safety is always the most important rule. As long as you remember your own code, the lines can be reconnected by matching similar letters or names. Please see the timing belt procedure in this section. Set the timing mark two dot marks of the camshaft drive gear at approximately a 25Â° angle by turning the hexagon wrench head portion of the intake camshaft with a wrench.
Remove the camshaft timing gear and chain from the intake camshaft and leave on the slipper and the damper. If not, turn the crankshaft exactly one revolution 360Â° and align the marks. So read ahead and plan ahead. If the wires are good proceed. Constantly be aware of the dangers involved in working on an automobile and take the proper precautions. The camshaft journal oil and thrust clearances should be checked. Tighten the bolts and nuts to 48 inch lbs.
There are commercial thread-locking compounds for ensuring that fasteners won't come loose, even if they are not torqued just right a very common brand is Loctite. Install the coils in the reverse order of removal. Although Toyota is not exactly as convincing as the competition, it has the proportions and the process that is perfect for the personality of the adventure. Uniformly tighten the bolts in several passes with final torque to 53 inch lbs. Pull it back out to make sure it's clean and threading properly.
The electrical charge will pass through the easiest path to ground, make certain it's not you. Uniformly loosen and remove the bearing cap bolts in several passes, in the sequence shown. Connect the ground strap to the engine hanger and the air intake chamber. Remove the three bolts, and then disconnect the engine wire from the cylinder head. Remove both cylinder head covers. Push the tensioner by hand until it touches the head installation surface, then install the 2 nuts.
Perform everything in the order in which the instructions say you should, even if you can't immediately see a reason for it. Remove the cylinder head cover. Place the gear over the straight pin of the intake camshaft. Print Back to Top Toyota Pick-ups, Land Cruiser, and 4 Runner 1997-00 Where to Begin Before beginning any procedure, read through the entire procedure. Use care to keep sealer out of the front bearing cap grooves.
Mount the hexagon wrench head portion of the camshaft in a vise. Perform this operation on both banks. Remove the camshafts using the following procedure. The head should be cleaned and inspected before installation. Using the micrometer, measure journal diameter, jot down the readings and compare the readings with those listed in the Specifications chart. The brand has gone on to produce a number of best sellers, amongst which the Camry, Corolla, Land Cruiser and Prius. Remove the heat insulator by loosening the two bolts and two nuts.
These bolts are: The 2. Toyota Spare Parts Catalogue Accessories catalog Toyota Japan, 10. A filter change is recommended. Then reverse the order of the above steps from e to c and repeat steps from a to f once again. Assemble the water bypass outlet and the pipe. Install the left side camshafts using the same procedure.
Toyota Rush Toyota Rush 2006 Service Manual — Operation, maintenance and repair manual + spare parts catalog for Daihatsu Be-go, Daihatsu Terios and Toyota Rush cars since 2006 with a 1. Do the same for the intake camshafts. Install the intake camshaft as follows: Since the thrust clearance of the camshaft is small, the camshaft must be kept level while it is being installed. Connect the engine wire to the engine as follows: A. For additional information, please refer to the following topic s : Timing Belt, Removal and Installation. Apply a light coat of engine oil on the threads and under the heads of the recessed cylinder head bolts. The cylinder on the compression stroke is defined as the 'event' cylinder, while the cylinder in the exhaust stroke is called the 'waste' cylinder.